COPYRIGHT WARNING:
All pictures and texts in this web page are the property of nomaallim.com. Any use of any part of those contents without the written consent of nomaallim.com shall be subject to legal procedures as per international and local laws in the concerned country. Using the name "nomaallim" or "nomaallim com" or "nomaallim.com" in the text describing the unauthorized copied content shall not constitute an exception and shall be sanctioned in accordance to the effective laws and proceedings.
All pictures and texts in this web page are the property of nomaallim.com. Any use of any part of those contents without the written consent of nomaallim.com shall be subject to legal procedures as per international and local laws in the concerned country. Using the name "nomaallim" or "nomaallim com" or "nomaallim.com" in the text describing the unauthorized copied content shall not constitute an exception and shall be sanctioned in accordance to the effective laws and proceedings.
- OVERALL DIFFICULTY INDEX: 2/10
- IF YOU HAVE NO TOOLS YOU PAY $3 TO GET THEM FOR THIS JOB
- IF YOU HAVE NO EXPERIENCE YOU SPEND 15 MINUTES TO CARRY OUT THIS JOB
- RISK OF BURNS, SEE BELOW
BEFORE YOU START
- Be careful not to touch any hot part of the engine.
- It is important to buy the perfectly matching sensor. Use both part numbers of the car manufacturer and sensor manufacturer to make sure.
- Such interventions are to be obviously carried out while the engine is Off. Disconnecting a sensor with the engine is On will trigger fault codes and could cause the engine to malfunction or stall.
|
|
|
DISCLAIMER:
Our pictorials are of informative nature and do illustrate works carried out by ourselves at our own premises for our own use and satisfaction.
Readers who envisage to carry out similar works inspired by the below method shall do this at their own risks and liability.
Our pictorials are of informative nature and do illustrate works carried out by ourselves at our own premises for our own use and satisfaction.
Readers who envisage to carry out similar works inspired by the below method shall do this at their own risks and liability.
Symptoms of a dirty or bad air intake pressure sensor
Is your check engine light on, your idle rough, or your fuel economy suddenly worse? A dirty or failing MAP (manifold absolute pressure) sensor could be to blame — and the fix is easier than you might think. In this guide you'll learn how the MAP sensor works, the classic symptoms of a bad one (including trouble codes P0106, P0107, and P0108), and how to clean or replace it yourself with basic hand tools in less than 30 minutes.
The DIY cost could be as low as $20-25 compared to $100 that a shop would charge for this repair.
The DIY cost could be as low as $20-25 compared to $100 that a shop would charge for this repair.
Where are the atmospheric and intake manifold temperature / pressure sensors located?
The intake manifold pressure sensor is located at the intake manifold as shown in the first picture.
The atmospheric pressure and temperature sensor is located on the throttle body.
The atmospheric pressure and temperature sensor is located on the throttle body.
Intake pressure / temperature sensors removal
1- Disconnect the sensor connector
2- Pull the sensor out. It is common to find the part of the sensor that holds to the intake manifold or throttle body, broken, sur to the aging of the plastic material. This is often the reason behind the necessity of replacing those sensors on the Trafic / Vivaro, rather than a faulty sensor or an check engine light.
2- Pull the sensor out. It is common to find the part of the sensor that holds to the intake manifold or throttle body, broken, sur to the aging of the plastic material. This is often the reason behind the necessity of replacing those sensors on the Trafic / Vivaro, rather than a faulty sensor or an check engine light.
Observe well your pressure sensors, if you find a lot of oil on them, then you need to further investigate the presence of oil in the complete intake tube, before and after the air filter, etc. in order to determine if some excess oil is circulating through the oil breather.
|
|
|
Cleaning the pressure sensor and other sensors
Take the sensor out as shown above.
Use a contact cleaner (electronic cleaner) to spray the sensor from a distance. Do not use carb cleaner or kerosene or diesel or any other product than an electronic cleaner.
Wipe it out immediately with a clean cloth.
Prior to refitting, clean well the sensor's environment, i.e. the air tube where it fits, then refit your cleaned or new MAP sensor. You may apply a thin coat of grease to the temperature sensor end, where it must be inserted into the throttle body, as this facilitates its mounting and reduces the risk of breaking it while you push it downwards its seat.
That's it, if your ECU had generated a P0106 code and your check engine light is on, connect your OBD-II scanner, erase codes and drive your vehicle.
Use a contact cleaner (electronic cleaner) to spray the sensor from a distance. Do not use carb cleaner or kerosene or diesel or any other product than an electronic cleaner.
Wipe it out immediately with a clean cloth.
Prior to refitting, clean well the sensor's environment, i.e. the air tube where it fits, then refit your cleaned or new MAP sensor. You may apply a thin coat of grease to the temperature sensor end, where it must be inserted into the throttle body, as this facilitates its mounting and reduces the risk of breaking it while you push it downwards its seat.
That's it, if your ECU had generated a P0106 code and your check engine light is on, connect your OBD-II scanner, erase codes and drive your vehicle.






