COPYRIGHT WARNING:
All pictures and texts in this web page are the property of nomaallim.com. Any use of any part of those contents without the written consent of nomaallim.com shall be subject to legal procedures as per international and local laws in the concerned country. Using the name "nomaallim" or "nomaallim com" or "nomaallim.com" in the text describing the unauthorized copied content shall not constitute an exception and shall be sanctioned in accordance to the effective laws and proceedings.
All pictures and texts in this web page are the property of nomaallim.com. Any use of any part of those contents without the written consent of nomaallim.com shall be subject to legal procedures as per international and local laws in the concerned country. Using the name "nomaallim" or "nomaallim com" or "nomaallim.com" in the text describing the unauthorized copied content shall not constitute an exception and shall be sanctioned in accordance to the effective laws and proceedings.
BEFORE YOU START
DISCLAIMER:
Our pictorials are of informative nature and do illustrate works carried out by ourselves at our own premises for our own use and satisfaction. Readers who envisage to carry out similar works inspired by the below method shall do this at their own risks and liability. |
What to know about the Timing Belt of the Renault Trafic II, Opel / Vauxhall Vivaro A, and Nissan Primastar, equipped with the gasoline engine Renault F4R
The Renault F4R (2.0 16V) and K4M (1.6 16V) engines share the same DOHC architecture and use the same timing tool needed for the timing belt replacement.
The timing belt must be changed every 60,000 Km and this operation requires replacing at the same time the timing belt tensioner, the timing belt roller-bearing, the crankshaft pulley bolt and the cylinder head plugs, all available within the same kit. It is indeed wise to replace the drive belt and its tensioner at the same time, while the water pump can be replaced every 120,000 Km.
The timing belt must be changed every 60,000 Km and this operation requires replacing at the same time the timing belt tensioner, the timing belt roller-bearing, the crankshaft pulley bolt and the cylinder head plugs, all available within the same kit. It is indeed wise to replace the drive belt and its tensioner at the same time, while the water pump can be replaced every 120,000 Km.
The below image shows the possible effects of a non-respect of the timing belt change interval on the K4M and F4R Renault engines, combined with an oil leak from the camshafts seals: the belt slipped sideways on the camshafts sprockets and began to rub against the cylinder head body, with visible damage to the belt.
|
|
|
Preparatory works for the timing belt change on the Renault Trafic and Opel / Vauxhall Vivaro
Remove the cylinder head plugs in order to later fit the F4R engine timing tool in there.
Lift the vehicle front of the vehicle, put it on jack stands and remove the right wheel and the inner fender mudguard in order to provide access to the crankshaft pulley. Keep the left wheel in place.
Remove all 4 COPs and spark plugs.
Remove all 4 COPs and spark plugs.
Fit the timing tool part that holds the two camshafts at their timing position.
Just rotate the engine by hand using the left wheel until the grooves of the camshafts end are aligned, and are below the cylinder head cover line.
Note: if you're removing the timing gear cover and camshafts for whatever reason, you do not need to align the camshafts at this stage, you will do so later when reassembling the timing gear; just dismantle and remove everything.
Just rotate the engine by hand using the left wheel until the grooves of the camshafts end are aligned, and are below the cylinder head cover line.
Note: if you're removing the timing gear cover and camshafts for whatever reason, you do not need to align the camshafts at this stage, you will do so later when reassembling the timing gear; just dismantle and remove everything.
Remove the drive belt, see the link further below to our dedicated tutorial.
Unscrew the crankshaft pulley bolt then remove the pulley by blocking the right wheel with a flat screwdriver inserted in the brake disc, while keeping the left wheel in contact with the floor.
Unscrew the crankshaft pulley bolt then remove the pulley by blocking the right wheel with a flat screwdriver inserted in the brake disc, while keeping the left wheel in contact with the floor.
Place a hydraulic jack underneath the engine and remove the right engine mount.
Click on the below link for our dedicated tutorial for the right engine mount and drive belt removal and refitting on Trafic and Vivaro.
Click on the below link for our dedicated tutorial for the right engine mount and drive belt removal and refitting on Trafic and Vivaro.
|
|
|
Removing the timing belt on Renault Trafic and Opel / Vauxhall Vivaro
The timing belt of the F4R engine has two covers, an upper one made of aluminum and a lower one made of plastic. Unscrew and remove all the covers bolts and take off the covers.
Use the hydraulic jack underneath engine, to raise or lower the latter so you can have an easy access to the bolts, if and when needed.
Use the hydraulic jack underneath engine, to raise or lower the latter so you can have an easy access to the bolts, if and when needed.
Release the timing belt tensioner by unscrewing its fixing bolt and take out the timing belt from underneath.
NOTE: the oil leaks that are visible in above pictures will be fixed and covered under other tutorials, this one being strictly for the timing belt replacement; see bottom of page for our proposed diagnosis method of oil leaks on F4R engine.
|
|
|
Refitting a new timing kit to the Renault 2.0 16V engine
Pull out the crankshaft sprocket using grip pliers, clean it along with both the crankshaft end and the crankshaft pulley with a strong degreaser, like carb spray (carburetor cleaning spray), then refit it to the crankshaft end making sure that the surroundings are also clean and free from oil.
The Renault F4R engine distribution kit includes the following parts:
- Timing Belt
- Timing belt tensioner
- Timing belt roller-bearing
- Crankshaft pulley bolt
- Cylinder head plugs
Now two persons are required for putting the crankshaft on its timing position.
Use the small pin provided within your engine timing tool kit, the longer one being the one of the K4M 1.6 16V engine.Ths pin just need to be inserted in its intended place, to the right of the oil level stick as shown in the second picture.
For finding the timing position of the crankshaft, proceed as follows:
Use the small pin provided within your engine timing tool kit, the longer one being the one of the K4M 1.6 16V engine.Ths pin just need to be inserted in its intended place, to the right of the oil level stick as shown in the second picture.
For finding the timing position of the crankshaft, proceed as follows:
- Insert a long rod like for example a ratchet handle extension in the spark plug well of cylinder No 1, the one adjacent to the gearbox.
- Ask your helper to rotate the engine using the left wheel while observing the rod; once the rod gets close to the TDC, the helper must be rotating the engine little by little while you try to insert the crankshaft pin, till it goes in there over its full length.
- If you cannot find the "hole", this means you're not on TDC, you're on the end of the exhaust stroke, simply rotate the engine another turn and try again.
Start by refitting first the new timing belt roller and tensioner, then start introducing the timing belt from top of engine downwards.
Important: if you had dismantled the camshafts prior to refitting the timing belt (again, this is indeed not required to replace the timing belt, rather for another purpose not described under this tutorial), then you need to make sure that your camshafts sprockets are not tightened and can turn freely, prior to attempting any timing belt refit or tensioning; if you're just replacing the belt, ignore this tip.
Important: if you had dismantled the camshafts prior to refitting the timing belt (again, this is indeed not required to replace the timing belt, rather for another purpose not described under this tutorial), then you need to make sure that your camshafts sprockets are not tightened and can turn freely, prior to attempting any timing belt refit or tensioning; if you're just replacing the belt, ignore this tip.
|
|
|
Place your timing belt on the camshafts pulleys first, then route it down to the crankshaft sprocket.
You may temporarily hold it with cable ties which you will later cut and remove.
Make sure the timing belt tensioner bolt is not tightened, so the tensioner can move freely around its axis.
You may temporarily hold it with cable ties which you will later cut and remove.
Make sure the timing belt tensioner bolt is not tightened, so the tensioner can move freely around its axis.
With utmost patience, pull the timing belt down with your fingers (do not use any tool or screwdriver) and insert it in the crankshaft sprocket while aligning both set of teeth. This is the most delicate stage of the whole timing belt change process, you will be able to do so only with patience and attention. Once the belt "catches" the sprocket teeth, push it inside.
Tension your belt using an allen key on the tensioner as shown in the second picture and tighten the belt tensioner bolt. Pay attention to the marks on the belt tensioner, you need to have them exactly matched, indicating the tensioned position of the belt.
NOTE: if you had removed the camshafts, you may now proceed with the tightening of the camshafts pulleys. Make sure to mechanically block the pulleys not to let the tightening of their nuts apply pressure on the belt or modify the timing setting; if you're just replacing the belt, ignore this tip.
Tension your belt using an allen key on the tensioner as shown in the second picture and tighten the belt tensioner bolt. Pay attention to the marks on the belt tensioner, you need to have them exactly matched, indicating the tensioned position of the belt.
NOTE: if you had removed the camshafts, you may now proceed with the tightening of the camshafts pulleys. Make sure to mechanically block the pulleys not to let the tightening of their nuts apply pressure on the belt or modify the timing setting; if you're just replacing the belt, ignore this tip.
Once done, remove the crankshaft pin, the camshafts alignment tool, and rotate your engine by hand for not less than two turns to make sure all goes smooth. DO NOT SKIP THIS TEST, since if you had made any mistake in your timing setting, your risk breaking your engine due to interference between valves and pistons!
Refit the spark plugs, COPs and cylinder head plugs, then start your engine and make sure all is smooth, you will notice an enhancement of your engine's sound. This is required prior to continue further, in order to make sure you did not do any mistake with the timing alignment, since you can still repeat your timing setting without having to remove covers, parts, etc.
Clean and refit the crankshaft pulley along with the new bolt; note how we blocked it using a few grip pliers, in order to be able to tighten its bolt.
Proceed with the drive belt and engine mount refitting, etc., by reversing above steps.
That's it!
Refit the spark plugs, COPs and cylinder head plugs, then start your engine and make sure all is smooth, you will notice an enhancement of your engine's sound. This is required prior to continue further, in order to make sure you did not do any mistake with the timing alignment, since you can still repeat your timing setting without having to remove covers, parts, etc.
Clean and refit the crankshaft pulley along with the new bolt; note how we blocked it using a few grip pliers, in order to be able to tighten its bolt.
Proceed with the drive belt and engine mount refitting, etc., by reversing above steps.
That's it!





































